Those things to pay attention to in the use of vacuum emulsifying machine

Have to say that the production of these products are inseparable from the vacuum emulsifying machine, but also suitable for pharmaceutical, food, fine chemical and other high viscosity materials in the industry. The equipment has the functions and advantages of fast homogenization, good homogenization emulsification effect (particle size up to 1um), heating cooling and vacuum degassing, production sanitary conditions in line with national standards, high thermal efficiency, reliable electrical control, stable operation, convenient operation and maintenance, low labor intensity and so on. ByTianfu vacuum emulsifying machine manufacturersTo sum upvacuum emulsifying machineThose things to pay attention to in use.

The vacuum emulsifying machine is composed of main pot, oil pot, water pot, electrical control system, hydraulic system, vacuum system and frame. The main pot is composed of a homogeneous stirring pot, a homogeneous mechanism, and a bidirectional stirring mechanism. Below we explain the use of vacuum emulsifying machine and matters needing attention.

1. After the production is completed, the vacuum emulsifying machine must be cleaned, so as to maintain the working efficiency of the stator and the rotor and play a role in protecting the sealing of the emulsifying machine. If necessary, a set of cleaning circulation device is designed and installed near the periphery.

2. After the emulsifying machine confirms that the machine seal cooling water is connected, start the motor. It is repeatedly required that the steering of the motor should be consistent with the steering mark of the main shaft before it can operate. Reverse rotation is strictly prohibited!

3. If liquid leakage is found at the shaft during operation, the pressure of the machine seal must be adjusted after shutdown.

According to the different media used by the user, the import and export filters must be cleaned regularly to avoid reducing the amount of feed and affecting production efficiency. Materials entering the working cavity must be fluid, and materials with dry powder and agglomerates are not allowed to enter the machine directly, otherwise, the machine will be stuffy and the vacuum emulsifier will be damaged.

5, it is strictly forbidden to metal chips or hard and difficult to break debris into the vacuum emulsifying machine working cavity, so as not to cause the work of the stator, rotor and equipment destructive damage.

6, in the use of the vacuum emulsifying machine before to develop the corresponding safety production procedures, to ensure the safety of operators and equipment. In the electrical control system, users should set up a safety protection system and have a good and reliable electrical motor grounding device.

7. If the process working chamber can be equipped with an additional insulation layer for cooling or heating the material, the coolant or heat transfer oil should be connected first when the machine is turned on. The working pressure of the insulation interlayer is less than or equal to 0.2Mpa, and it must be heated or cooled to the normal working temperature, turned on and turned on when the processing temperature is required.

When the emulsifier is used in a flammable and explosive working environment, the corresponding level of explosion-proof motor must be selected.

9. Usually, the cooling water of the mechanical seal is connected before the vacuum emulsifier is opened, and the cooling water is shut down before the machine is shut down. Tap water can be used for cooling water. The material must enter the working cavity before starting the machine, and ensure that it does not run under the condition of material breakage to avoid idling, which may cause the mechanical seal to burn out due to high temperature or affect the service life. Cooling water inlet and outlet fittings are equipped with hose size inner diameter.

10, usually only through the high weight to the TRL1 pipeline equipment into the material, the feed must be continuous input, to maintain the material has good fluidity. However, when the fluidity of the material is poor, when the viscosity is ≧ 4000CP, the inlet of SRH pipeline equipment shall be equipped with a delivery pump with a pumping pressure of 0.3Mpa. The pump should be selected as a colloid pump, and its flow rate should match the flow range of the selected pipeline emulsifying machine.

11. The vacuum emulsifying machine needs to check the stator and rotor regularly. If it is found that the wear is too large, the corresponding parts should be replaced in time to ensure the effect of dispersion and emulsification.

When using a vacuum emulsifier, the liquid material must be continuously input or kept in a certain amount in the container. Should avoid empty machine operation, so as to avoid the material in the work of high temperature or crystallization and solidification and damage to the equipment!

13, vacuum emulsifying machine in the course of operation in the event of abnormal sound or other failure, should immediately stop the inspection, to be removed after the operation of the fault. The working chamber and stator and rotor shall be cleaned after shutdown.

The above is today Tianfu vacuum emulsifying machine manufacturers to bring you about the relevant introduction of vacuum emulsifying machine, for your reference!